DISCLAIMER – FOR OFF-ROAD USE ONLY
NXT STEP PERFORMANCE, INC. exhaust systems products are sold for off-road use only. All performance modifications and installations are at the customers own risk. NXT STEP PERFORMANCE, INC. hold no responsibility either implied or otherwise for mechanical, electrical or other failure when using any aftermarket performance products. Items sold for off-road use only are illegal in many states and provinces and are intended for racing vehicles which may never be used on a public road.
By purchasing any aftermarket performance product, the customer takes full responsibility for any use, and/or misuse of the product and agrees that NXT STEP PERFORMANCE, INC. holds no responsibility for any consequences, legal, or other, of such use and/or misuse.-----Limited lifetime warranty: All NXT Step Performance exhaust systems come with a limited lifetime warranty against manufacturing defects for both materials and quality. Warranty is valid to the original purchaser and original vehicle the exhaust system is installed. You must contact your original retailer in order to get the warranty process initiated. NXT Step Performance, Inc. Will examine any returned product and has the right under this warranty to replace or repair the item. This warranty does not include the cost of removal and installation of the exhaust system and any shipping/freight costs associated with returning items to the retailer. Any changes, modifications or systems used for racing purposes will void all warranties, exchanges and/or refunds.
2016 – 2018 CAMARO 2.0L Turbo Muffler Delete System (REAR SECTION ONLY)
INSTALLATION INSTRUCTIONS
NXT STEP PERFORMANCE recommends that an exhaust shop or professional after-market parts installer, who has all the necessary equipment, tools and experienced personnel needed for proper installation should perform the installation of this system.
Never work on a hot exhaust system. Serious injury in the form of burns can result if the vehicle has been in use and the exhaust system is hot, allow vehicle to cool for at least 1 hour. Always wear eye protection when working under any vehicle.
It is our recommendation that you use a hoist or hydraulic lift to facilitate the installation of your new NXT STEP PERFORMANCE exhaust system taking all under car safety precautions. Once this has been done, you may begin the removal of your old exhaust system from your vehicle.
WARRANTY NOTICE
By installing your NXT STEP PERFORMANCE exhaust system, you indicate that you have read this document and you agree with the terms. It is the responsibility of the purchaser to follow all installation instruction guidelines and safety procedures supplied with your NXT STEP PERFORMANCE exhaust system. NXT STEP PERFORMANCE assumes no responsibility for damages occurring from misuse, abuse, improper installation, improper operation, lack of responsible care, or all previously stated reasons resulting from incompatibility with other manufacturer’s products and/or systems. If you should have any questions regarding our warranty policy, installation, or any other matter pertaining to your new NXT STEP PERFORMANCE exhaust system, contact us via email - [email protected]
Warning: Use extreme caution during installation. Torque all fasteners according to manufacturer’s torque values and tightening sequence. DO NOT use air impact tools to tighten fasteners on NXT STEP PERFORMANCE exhaust systems. Use of such tools may result in bent flanges or gasket contact areas leading to exhaust leaks.
- From under the vehicle measure the length of the new muffler against the factory muffler and mark where the factory piping will need to cut. This cut position is the same on both LH & RH side Exhaust Pipes.
- Confirm the mark is in the correct location and cut the pipe along the marked cut line.
- Remove the muffler from its rubber hangers and discard the old muffler. De-burr the end of the exhaust pipe.
- Slide the exhaust clamp onto the new exhaust pipe. Install the new muffler onto the rubber exhaust hangers and slide the muffler onto the exhaust pipe.
- Position tip in rear valence and tighten the clamp bolt to 32-35 ft.lbs. torque.
- Repeat instructions for the opposite side.
- Before starting your vehicle, make sure to check all wires, hoses, brake lines, body parts and tires for safe clearance from the exhaust system.
- Start vehicle and check for any leaks. If any leaks are found, determine cause (such as loose or incorrectly positioned clamp) and repair as necessary (When you first start your vehicle after the installation of your new NXT STEP PERFORMANCE exhaust system, there may be some smoke and fumes coming from the system. This is a protective oil based coating used in the manufacturing of mandrel bent performance exhaust tubing. This is not a problem and will disappear within a very short period of time after the exhaust has reached normal operating temperatures).